How To Replace A Faulty Door Seal on A Washer Dryer

Washer dryers offer the speed and convenience needed by modern households to complete the tedious, and often daily, task of cleaning and drying clothing. Although they may save time in the long-run, washer dryers are, in fact, the least reliable of all the large kitchen appliances; a symptom of combining the function of two machines in one. As a result you may find yourself shelling out extra cash on your washer dryer far more often that you’d like.

Problems with washer dryers are often more complex to fix than those encountered by a stand-alone washing machine or tumble dryer. Some of the ailments afflicting them do need to be tackled by a professional plumber. There are, however, a few minor repairs that you can and should complete yourself. With the right tools to hand and the correct replacement parts purchased, you could save a fortune on costly call-out charges and have the satisfaction of being a DIY genius maytag dryer repair los angeles.

Washer dryer owners commonly complain that their machine repeatedly leaks water when in use. This could be symptomatic of a bigger problem, however nine times out of ten simply replacing a door seal that’s been made ineffective by limescale and grease build-up solves the problem. New seals can be purchased from any major DIY store, just be sure to note down the make and model of your machine to ensure the right fit. Line up both a Philips and flat-head screwdriver and a plastic cable and you’re ready to begin working through these easy instructions.

1. Find the plastic retaining clip that holds the existing door seal in place around the drum of the machine. This will be on the interior side of the door, hidden by the rubber lip. Remove and set aside.

2.Find the two screws on the inter-lock mechanism of the door, usually set to the right hand side. Unscrew and set aside.

3. Removal of the washer dryer’s frontage is begun by finding the two large screws at the back of the machine that keep this section fixed in place. One is found at either side; unscrew these and set aside. You can now lift the main front panel across the machine off completely.

4. Take out the machine’s soap drawer (the box found on the front where washing powder or liquid is added.) Removing this will expose two hidden screws; unscrew and set aside.

5. The front section of the machine that displays its operating instructions can now be lifted off easily.

6.There is now only one piece of the front panel to left remove. You will find four more screws holding this panel on; two at the top and two behind the kick plate. You can now lift the remaining piece away.

7. Find the machine’s drying duct. This is a rectangular shaped opening to the right hand side of the door seal. Unplug this by sliding the door seal off it.

8.Release the inner retainer of the door seal (now the only thing holding it on) by wedging your flat-head screwdriver into its clip. Once this is done, the entire faulty door seal can be pulled off and thrown away.

9.Take your new door seal and place it up against the drum of the machine, checking that it’s in the right position by lining up its built-in vent with the drying duct you have just disconnected. Push the opening of the drying duct through the vent in the new door seal and use a cable tie to hold it firmly in place.

10. It should now should be easy to feel the door seal’s interior lip around the machine’s drum. Once this is done, you can fasten the machine’s inner retainer back in place.

11. Screw the door inter-lock mechanism back in and repeat with the front and top panel. Replace the soap drawer.

12. The last thing you need to do is feed the outer lip of the new door seal around the exterior of the drum and put the retaining clip back on the secure.

Important Reason to Exhaust a Clothes Dryer Outside

Occasionally people will mistakenly vent their dryer indoors believing that this is an effective way to add heat their home. However, there are several reasons why this is a bad idea. If you know someone who vents their dryer indoors, you may want to share these reason why they should stop immediately.

To meet code requirements

Codes typically require that the dryer duct be no more than 25 feet long. It should be 2.5 feet shorter than 25 feet for every 45-degree bend and 5 feet shorter for every 90-degree bend. For dryer venting that exceeds 25 feet in length, a booster fan is required. Ducts should have a diameter of 4″ and be made of smooth metal. Plastic venting should never be used because they collect lint, can be crushed and impede airflow. The male ends of the duct should face the direction of the airflow. The duct exhaust must not mix with or pass through other systems, such as the return-air plenum, because heat, moisture, and combustion gases could mix with the conditioned air in the home kenmore dryer repair los angeles .

The vent should lead to the outside, and be at least 3 feet from any other opening. It should also have a termination cap and damper to keep vermin from entering the home. Because it could impede airflow, a screen at the end of the vent opening should not be installed.

To remove heat and moisture

The dryer heats the air in the drum to around 150F resulting in moisture leaving the clothing and saturating this hot air. A moist humid atmosphere is perfect for mildew conditions. Also, allowing the moisture to vent indoors results in the recirculation of moist air which will cause long dry times.

To remove dangerous fumes

Carbon Monoxide (CO) is a lethal poison that is produced when fuels such as gas are burned. It can rapidly accumulate even in areas that might appear well ventilated. Because CO is colorless, tasteless, odorless and non-irritating, it can overcome an exposed person without warning. It frequently produces weakness and confusion, depriving the person of the ability to seek safety.

To remove lint from the dryer

The lint screen of a dryer does a great job of removing lint from the dryer but it does not remove it all. When this lint is prevented from flowing freely, it can accumulate in the vent and/or interior dryer resulting in a fire hazard. It is very important that the lint screen be cleaned with each load and the dryer venting is cleared on a yearly basis.

Although it may seem like a good idea during the cold winter months to vent the dryer inside the home but there are several reasons to avoid this. Moisture damage to the home, a fire hazard and possibly death should be convincing reasons to make sure venting is always clear and always vented outdoors.


4 Practical and Affordable Ways to Repair Your Acrylic Tub

Techniques on acrylic tub repair completely differ depending on the problem that needs to be solved. It can be a D.I.Y. job repair, or you can enlist the help of professionals. So, before you spend on a new unit, try to explore some practical and affordable acrylic tub repair techniques first.

The great thing about an acrylic bath tub is that it’s relatively easy to repair. If ever its surface is scratched or grows dull, it would still look pretty decent because its color is the same from the outside to the inside. Other tub types, like cast iron clawfoot tubs, are quite complicated to repair.

Shallow and deep scratches can be remedied kitchenaid dishwasher repair los angeles. You can do it by using a soft cloth material with liquid or cream-based polisher to rub the scratched area. If the scraping is deep, you can use fine sandpaper (1500 grit). Just make sure to moisten the area first, and then apply a liquid polisher after sanding.

Bath tub liners are not always the most economical options, but they are definitely cheaper than purchasing a brand new tub. You really don’t have to wait for ages for this to be installed. If you are worried about after mess cleanup, well, there is virtually none.

However, there are also a couple of disadvantages linked to using tub liners to cover up appearance defects of tubs. These could cause mildew and mold to develop due to trapping of water. They don’t also feel solid under your foot. And their costs could be equal to or more than refinishing a tub.

A bath tub refinishing can be a valuable option. The process of refinishing a bath tub simply involves eliminating impurities, make the necessary repairs, and put on new finishing, so your bath tub would look almost spanking new again. But in order for this to work for you, you should let the professionals do it.

The cost of refinishing a bathtub completely varies for each company. More or less, you can expect to spend around $300-$500. A refinishing job that’s done properly can extend your bathtub’s life up to 15 years. To find a refinisher, you can check out the website of the Bathtub Refinishing Association of America.

Sometimes, you really do not need to apply a new glazing or paint just to make your tub look immaculate again. You can just regularly clean it to remove stubborn dirt spots and deposits. You can use mild dishwashing liquids or bathroom cleaners. Always avoid using harsh solutions, like acetone.

History of Samsung

Samsung began life in South Korea being founded by Lee Byung-Chull in 1938 a very hard working and ambitious man. He always approached any market that he wanted into with the attitude that his company would quickly push to top of that particular field. His business started as an export company dealing in fruit, vegetables and dried fish and had been doing fine building up to having forty workers at his trading company in Seoul until in 1950 when the communist’s invaded the south. Despite losing a lot of stock and money he relocated to Suwon in 1951 and in 2 short years his company increased its staff and profits by a staggering amount estimated at 2000%. Lee built his first production factory after the war in 1953 which was a sugar refinery until now he had worked only as a trader selling other peoples goods. Now that Lee had financial security he branched into opening department stores for trading then started selling insurance policies and securities samsung appliance repair pasadena.

The 60s and 70s saw the rise of Samsung Electronics which was founded in 1969 and benefited greatly from the policies of the then president Park Chung who strived to help anyone who was building a profitable company within South Korea. He would provide financial help when required and even banned foreign manufacturers from selling within his country to eliminate competition and allow Korean companies to grow stronger. In another very shrewd move he allowed certain companies access to Korea’s markets but to do so they had to supply technology to Korea’s industry which allowed Samsung Electronics to be able to produce electronic boards and chips.

This allowed samsung to produce their own products and soon they had a range of household appliances such as fridges, freezers, washing machines and air conditioners sold at home and exported to foreign markets. The early 70s saw the company borrow money and branch into the booming communications industry building TV’s and audio equipment and opening their own television station called the Tongyang Broadcasting Company . It was also in the 70s that Samsung branched into heavy industrial projects such as shipbuilding, petrol refineries and home electronics. Various branches of Samsung were created such as Samsung Shipbuilding, Samsung Precision Company and Samsung Heavy Industries Company.

Throughout the 80s Samsung continued to grow in all the markets it had already entered and still continued to enter new ones including aerospace, genetic engineering and nanotechnology which it incorporates into it’s washing machines. They built large manufacturing plants in Portugal, England and New York between 1982 and 1987 for production of electronics and home appliances. It was in 1987 after running the company for over fifty years that Lee Byung – Chull passed on leaving the company to his son Kun – Hee Lee who took the title of chairman.

Today the company still grows and is a household name for appliances and regarded as one of the top five industrial giants on the planet. They are also the official sponsors of the Olympic games from 2010 to 2016 taking in both the Olympic games and the winter Olympic games

Samsung will officially sponsor the Olympic Games and the Olympic Movement for the next eight years, a deal that covers the Vancouver Olympic Winter Games in 2010, the London Olympic Games in 2012, the 2014 Olympic Winter Games, and the 2016 Olympic Games.

How to Choose Between Refrigerator Repair and Replacement ?

Are you struggling with a fridge that has started leaking or has stopped cycling on and off? Whatever the problem, you need to choose between refrigerator repair for the broken parts or total refrigerator replacement. Here are some facts to consider before making your final decision.

If you’re like most homeowners in America, then you rely on a fully functioning refrigerator for all of your food storage and daily meals. Helping you prevent perishable items like milk and cold cuts from spoiling, your refrigerator is vital to everyday food safety and the overall health of you and your family. Given that our refrigerators are in constant use, it’s easy to forget that they’re just like any other appliances in that they weren’t built to last forever. In time, one or more of your unit’s parts will wear out, and you’ll be left with a decision: repair it or replace it maytag refrigerator repair pasadena?

First, let’s talk about the pros and cons of refrigerator repair. Whether you choose to repair the unit yourself or hire an appliance repair technician to perform the work for you, repairing the broken part of you refrigerator will cost significantly less than replacing the whole entire unit. However, the downside of opting for refrigerator repairs is that you’ll need to make certain that at least one qualified individual is at the helm. That means you’ll either have to study a refrigerator repair manual intensively or hire a licensed repairman to complete the job for you. The first option allows you to save even more money but will cut a big chunk into your spare time; the latter option requires you to pay for the outside labor but will get the job done without detracting from your weekend plans.

The alternative to repairing your refrigerator is, of course, replacing it altogether. Many homeowners take this course of action when they feel that their current fridge has become outmoded and worn out, concluding that this particular malfunction is just the first in a series of malfunctions that will only increase in severity as time goes on. Generally speaking, this is sound logic when it comes to units that are nearing double-digits in age.

However, the price of a brand-new fridge more than doubles the average cost of refrigeration repairs, so you’ll want to be sure about the poor condition of your fridge before making such a sizable purchase. Moreover, while purchasing a new fridge will certainly save time–as you won’t have to wait to study a refrigerator repair manual, order parts, or wait for the arrival of a repairman–you will have to consider the difficulties of installing it and properly disposing of the old one. This is an extremely important consideration, given that improper disposal can lead to hefty fines on top of what you already paid for your new fridge.

In short, your choice is between saving money and saving future hassle. Hiring a refrigerator repair service or performing the necessary refrigerator repairs yourself will be significantly more budget-friendly (price range for refrigeration repairs: $200 – $270; price range for all-new refrigerators: $400 – $3,500), while replacing your worn-out model with a new one will prevent future inconveniences from cropping up all over again. It’s a tough decision, but don’t take too long to think about it: You can’t go much longer without a working fridge!

Front Load Washer Tips

Front load washers are more efficient, using just 13 gallons of water verses 35 gallons for a typical top load machine. Front load machines use less energy. Front load machines also cause less wear on clothes. However, occasionally, consumers may comment on longer wash times, increased washer vibration or movement, clothes coming out wet, or that washer paused and consumer had to restart.

Clothes coming out too wet

1. Adjust out-of-balance load. It is best to washer similar fabrics in reasonable amounts for best results.
2. An extremely heavy load can lower the wash basket below the drain pump inlet resulting in wet clothes (water in basket during spin) washer repair altadena.

Clothes coming out Damp
1. Many washers spin at 2 different speeds ranges based on load and balance. A slower speed spin will cause clothes to retain more moisture.

Long Wash Times
1. Select SpeedWash set on Normal Soil for fastest possible wash cycle. Wash similar fabrics together to reduce the number of rebalances.

2. Depending on the wash cycle selected, initial wash cycle time estimates vary from 40 minutes for the shortest cycle to nearly 3 hours for the longest cycle. In addition, out-of-balance load rebalancing can add as much as 63 minutes to a given cycle. Adjust an out-of-balance load to minimize rebalances and shorten overall wash cycle time. It is best to wash similar fabrics in reasonable amounts for best results.

3. Legs out of adjustment. Each of the 4 legs should be adjusted to carry equal weight to reduce rebalancing.

4. Too much or wrong detergent creating excess foam and triggering pressure switch. During Washer, if the machine determines there is too much foam, it will stop rotating the basket and turn on both the drain pump and the water valve to flush excess suds. The pump may run for an extended period of time until foam level drops below the machine set-point. This can add an hour or more to the cycle time.

Re Leveling the Washer
1. Ensure the unit is level and all four leveling legs are properly adjusted and securely on the floor. The objective is for each of the four legs to carry equal weight, four on the floor. As little as ¼ or ½ turn on a single leveling leg can be significant. A helpful quick check is to place your left hand on the top left front corner and your right hand on the top rear corner. Then, push the washer in the direction of your hands and note force required to remove the weight from the front leg.

Now, reverse hands, right in top right front corner and lift in top left rear corner and not the force required to remove weight from the front leg. The two forces should be equal.

Why does the washer move?
1. Both the front load washer and pedestal are made o move. They absorb the energy from spinning to reduce vibration. If they were rigid, and did not move, they would hammer the floor as the basket spins.

2. Top load washers vibrate side-to-side and front-to-back. Front load washers vibrate up and down. While accelerating into spin, the legs on one side push harder on the floor and the other side push less. This force can be very large. A load of clothes and the machine together could weigh 400 to 500 lb.

3. Front load washers are more efficient using just 13 gallons of water verses 35 gallons for a top load machine. Front load machines have a shorter dryer time and use less energy. Front load machines cause less wear on clothes; however, Front load washers vibrate more in spin. Front load washers can spin at more than 1000 rpm verses just 500-500 rpm for top load washers.

4. Below 12 rpm, the front load washer cannot calculate or adjust to out-of-balance load conditions. The solution to a slow speed vibration issue is to adjust or change the load. It is best to washer similar fabrics in reasonable amounts for best results.

5. Front load washer must be level for the dispenser to work properly.

6. Each of the four front load washer legs must carry approximately equal weight to minimize movement and vibration.

7. Excessive vibration can be caused by a minor un-leveled condition associated with floor tiles. Floor tiles generally vary slightly in height once their installed. If your washer legs move to the left or right and move to a adjacent “lower” tile, the vibration will increase dramatically. Floors should be as solid as it could with no “give”. If you can stand next to a washer during the spin cycle and feel the floor moving, the problem lies with the floor and not the washer.

Appliance Repair Safety

Repairing your own appliances can be a cost-effective solution to malfunctions. But for your safety, make sure you take the necessary precautions!

Fixing your own appliances when they break down can be a great way to save money–but only if you do it right! One of the biggest concerns with DIY appliance repair is safety, so before you dive headfirst into that washer repair or fridge malfunction, make sure that you’re taking all necessary precautions to protect yourself, your appliance, and your home appliance repair pasadena.

Unplug It!
All appliances use electricity, even gas appliances, so make sure that you unplug the power source BEFORE you start working on the appliance. For projects like gas dryer repair, also make certain the gas line is completely shut off to prevent potentially deadly gas leaks.

Don’t Go It Alone
Unless you’re a trained appliance repair technician, you probably can’t just look at a faulty dishwasher or malfunctioning fridge and know exactly what the problem is. So why try to go it alone? There are myriad resources, from your appliance’s owner’s manual to online forums, tutorials, and troubleshooting guides, so use these materials to help guide you through both the diagnostic and repair stages.

Safety Equipment
As with any (and all) home improvement and repair projects, you’ll need appropriate safety gear for your appliance repair job. Safety glasses are a must, as are work gloves to protect your hands from sharp metal edges. You’ll also want an electrical multimeter tool. This handy gadget allows you to safely confirm that no power is flowing through a particular connection, a crucial step to avoid electrical shocks and electrocution when working with any type of electric appliance or wiring.

Remember, if you begin an appliance repair and end up getting stuck, it’s likely that you’ll actually end up paying more than if you had called the appliance repairman from the get-go. This is because the repair technician will probably have a harder time with diagnostics once you’ve tinkered with the appliance, and in cases where the machine is partially dismantled, the pro might even have to put it back together again to troubleshoot the appliance. As a result, it’s important to only attempt an appliance repair, large or small, if you’re fully confident you can resolve the problem not only safely, but also completely.

Do-it-yourself appliance repairs can be a cost-effective solution when your fridge, dishwasher, or other appliance starts acting up. However, in order to maximize your savings–and your success–make sure you’re smart about both safety and your own skill level. If you approach the dishwasher repair, oven repair, or other project right, you’ll be able to get that trusty old appliance back to running smoothly once again.

Three Online Sources for Dishwasher Parts

Sometimes, fixing your own appliances is not difficult and can save you a great deal of money on service calls. If you want to find dishwasher parts to replace minor problems or fix major ones, you can find affordable, quality dishwasher parts from several online providers.

A-1 Appliance Parts

A-1 Appliance Parts gives customers a wide variety of appliance parts to choose from. Dishwasher parts are easy to find with A-1 Appliance Parts’ database search feature. On their home page, you can search by your dishwasher’s model number or more specifically by the part number if you know it. A more general search begins with the appliance type, in this case a dishwasher, down to the brand then to the specific part you need. This way even if you do not know the model number of the part in question, you can still find the dishwasher part that you need. They carry parts for dishwashers made b y GE, Maytag, Whirlpool, and Frigidaire as well as repair manuals to help you in your do-it-yourself dishwasher repair project kitchenaid dishwasher repair los angeles .

A-1 Appliance Parts assures their customers that they handle each part carefully. They promise personal, live operators when you call during regular business hours. Your dishwasher parts exchanged through A-1 Appliance Parts will come with a one-year warranty. If you get your dishwasher part only to realize you do not need it, you can return it within 30 days for full credit as long as it was not installed or ordered as a special order.

Appliance Aid

This company found on the internet also offers an extensive selection of dishwasher parts. Models they provide parts for include Whirlpool, Kenmore, Kitchen-aid, Maytag, Magic Chef, Performa, Jenn Air, Kelvinator, Hotpoint, GE, Moffat, McClary, Tappan, and White Westinghouse. Their website allows you to search by brand and part descriptions or by part number and model number if you have that information. Many links are shared with A-1 Appliance Parts.

Part Store

Another website to find your dishwasher Part Store carries all the major brands. They also offer the option to buy compatible equivalents that could save you money on your do-it-yourself dishwasher repair. They have an extensive database to determine if the dishwasher part will fit with your specific model. They have an easy return policy where you call for an authorization number to return the part within 30 days. However, the warranty on their parts is only 30 days unless there is a warranty from the manufacturer. Returns must not have been installed and must be in resalable condition. Credit is given once it is received and determined to fit these conditions.

For the handy person who would like to repair the dishwasher on his/her own, the World Wide Web offers many opportunities to find dishwasher parts at affordable prices. These three sources are a good starting point to find the dishwasher part that you need.

Tips on Saving Money on Frigidaire Refrigerator Parts

Your Frigidaire refrigerator is on the blink and in need of servicing, so now you have to buy a replacement part for it. Should you buy a new part or a used part, because after all, what is your refrigerator in total now but a conglomeration of used parts anyway. Also, if you are going to go with the used part idea where can you buy one?

New Online Sources

Over the course of the past several years more choices and options have come available for people buying used and new parts to repair their appliances, including Frigidaire refrigerator parts. Its all the result of the Internet, because virtually all of these new sources are online suppliers whirlpool refrigerator repair los angeles.

Be Prepared

However; if you have never purchased new or used replacement parts for an appliance, there are several things that you are going to have to take in to account. The first thing that you will want to keep in mind, is that the onus is on you to have the information that you will need. The person on the other end of the line may be able to be somewhat helpful but don’t expect an appliance repair “genius”.

Save Your Stuff

Remove the old part that you are going to have replaced and save all the screws, washers or gaskets etc. This is because new ones may not come with the new or used part that you order. Place them in a baggie, tie it or seal it closed and place it in a safe place where you can find it when you need it.

Model and Part Numbers

Make sure that you write any “part” numbers down that are printed or stamped on the part that you will be replacing. Also, find the model number if you can and write that down also. After you have all of this in hand, then you are ready to begin your search for your new or used Frigidaire refrigerator part.

3 Easy Appliance Maintenance Tricks

Replacing an appliance can be cumbersome, expensive, and downright inconvenient. Most appliances are built to last for many years of continuous use; however, in some cases, improper use or general wear and tear can make your favorite appliance deteriorate much faster than normal.

Making your Appliance Last

If you correctly use an appliance – like only washing dishwasher-safe dishes in the dishwasher, or not over-loading your washing machine – the affects of general wear and tear may not appear as quickly. In addition, taking care of your appliance by scheduling regular maintenance repairs and paying attention to the performance of the appliance can greatly increase its longevity lg appliance repair pasadena.

Here are three easy appliance maintenance tips and tricks that you can add into your appliance care tool belt to help you avoid those expensive repair bills:

1. Check your Oven Door Seal

If you have an oven that needs frequent maintenance, or your oven recently started to take a long time to cook food, you may have a faulty oven seal. Over time, the oven’s seal eventually wears away, and this causes nearly 20% of the oven’s heat to escape.

An oven that can’t maintain a consistent temperature might undercook food, burn baked goods, or over-cook your holiday meal. Plus, losing 20% of your oven’s heat means that your electricity bill significantly increases.

If you think that your oven’s seal is damaged or loose, open the oven door and run your hands around the rubber gasket at the edges of the door. If there are any broken or torn places in the seal – or if parts of the seal are deformed – you may need to replace your oven seal.

2. Replacing Filters

Many people forget to replace or clean out the filters in their appliances. Letting lint pile up in the dryer or soap scum build up in washing machines can be detrimental to your home as well as the appliance. Dirty or worn out filters hinders your appliances’ ability to do its job.

This may appear to homeowners that the appliance frequently wears out or is faulty. However, in most cases, the real reason behind the poor performance is a dirty filter.
If you have an appliance that isn’t performing as well as it should, take out the filters and remove any dirt, grime, soap scum, or other build up that has occurred through frequent use. In some cases – like your refrigerator’s water filter – you may need to replace the filter entirely. This may seem slightly expensive, but it will save you the expense of paying for the entire appliance.

3. Replacing Washing Machine Hoses

Washing machine floods may be your worst nightmare. Most in-home water damage comes from a leak in a washing machine hose. Homeowners should frequently check their washing machine hose at least once every year if not bi-yearly.

If you have had a washing machine for longer than a year, you should check your hose as soon as you can. In order to do this, remove the panel on the machine and search for cracks or leaks in the hose. If there is a crack or leak in the hose, you may need to replace it. You can find these hoses at a local appliance repair shop, or you can return to the place you purchased the appliance and acquire a new hose.